Search found 700 matches
- Fri Dec 31, 2021 12:16 pm
- Forum: Pro Audio Design
- Topic: Texar Prism clone prototype Finished Version
- Replies: 77
- Views: 910371
Re: Texar Prism clone prototype Finished Version
I was trying to get 470uf 50v in a 10mm diameter. I usually use Nichicon HE but all I could find are Epcos at Digikey.
- Fri Dec 31, 2021 11:24 am
- Forum: Pro Audio Design
- Topic: Texar Prism clone prototype Finished Version
- Replies: 77
- Views: 910371
Re: Texar Prism clone prototype Finished Version
Are there any issues sourcing the MLCC caps? I have an open cart at Mouser right now for another project and haven't checked them. I’ve noticed lately that Mouser is picked over. I couldn’t get some non exotic aluminum electrolytic caps in the form factor I needed in any brand. Digikey has much bet...
- Wed Dec 15, 2021 6:35 pm
- Forum: Pro Audio Design
- Topic: Mid Side M-S Matrix Uses No Precision Resistors
- Replies: 271
- Views: 619702
Re: Mid Side M-S Matrix Uses No Precision Resistors
After thinking about it again I think the 8 pole 3 pos switch is the best answer. Signal Input goes to Wiper 1-4. Attenuator Input is from Wiper 5-8. In Position 1, Wiper 1-4 Signal input connects to Poles 1-4. Poles 1-4 are jumpered to Poles 5-8. Poles 5-8 feed Attenuator Input. In Position 2, Pole...
- Wed Dec 15, 2021 3:59 pm
- Forum: Pro Audio Design
- Topic: Mid Side M-S Matrix Uses No Precision Resistors
- Replies: 271
- Views: 619702
Re: Mid Side M-S Matrix Uses No Precision Resistors
I'm suggesting that you put the MS encoder, to monitor Mono or Difference, ahead of the Monitor attenuator. That way you have a low impedance source to drive the H-pad and you don't have to worry about the MS loading the pad. What advantage is there to it being post? It is ahead of the monitor atte...
- Wed Dec 15, 2021 2:35 pm
- Forum: Pro Audio Design
- Topic: Mid Side M-S Matrix Uses No Precision Resistors
- Replies: 271
- Views: 619702
Re: Mid Side M-S Matrix Uses No Precision Resistors
I'm trying to mimic the specified 1246 input with a 6dB pad. Shouldn't I be doing that for center channel headroom? If the 1246 could be made to have a 100K input impedance I'd be good.
- Wed Dec 15, 2021 1:01 pm
- Forum: Pro Audio Design
- Topic: Mid Side M-S Matrix Uses No Precision Resistors
- Replies: 271
- Views: 619702
Re: Mid Side M-S Matrix Uses No Precision Resistors
I would like to use the Encode half of the M/S board(s) in my monitor controller for Mono and Difference. The Monitor Controller uses a balanced H pad with a 10K input impedance when both are fed in parallel. I would like the input to the M/S board to have an input impedance of 100K so the input sti...
- Wed Sep 08, 2021 1:25 pm
- Forum: Pro Audio Design
- Topic: "MS Mini" Basic Mid Side Board
- Replies: 6
- Views: 6422
Re: "MS Mini" Basic Mid Side Board
I still have a pile of the V1 PCB's that I get good use out of. This is a nice addition to the line.
- Mon Aug 16, 2021 2:34 pm
- Forum: Pro Audio Design
- Topic: Texar Prism clone prototype Finished Version
- Replies: 77
- Views: 910371
Re: Texar Prism clone prototype
Sounds like a good plan.
- Mon Aug 16, 2021 12:33 pm
- Forum: Pro Audio Design
- Topic: Texar Prism clone prototype Finished Version
- Replies: 77
- Views: 910371
Re: Texar Prism clone prototype
Will it be possible to bring any of the 'under the hood' parameters like attack, release and ratio, out to the front panel? To use it in a production as opposed to broadcast environment I think that would be necessary. Really cool project though. Following closely.
- Wed Aug 04, 2021 12:36 pm
- Forum: Document
- Topic: Digikey leadtime trends
- Replies: 3
- Views: 5347
Re: Digikey leadtime trends
I think Wayne mentioned it in another post but I've been finding Digikey has stock of many items, like Meanwell PSU's, that Mouser is out of. Mouser is my first call but I check Digikey if Mouser is out of stock.